IV fluids are also known as a saline solution. This sterile solution is made of sodium chloride and water. This liquid is the foundation of every IV solution, providing essential hydration, diluting medications, and facilitating the delivery of vitamins throughout the body.

IV fluids help maintain a patient's hydration, electrolyte and blood sugar levels while undergoing surgical procedures. Clinicians are also able to administer warmed IV fluids directly into a patient's bloodstream, as it is common for a patient's body temperature to decrease slowly while he or she is sedated.

STANDARD IV & ELECTROLITES

- NaCl 0.18 – 2.7%

- Glucose 2.5 - 50%

- Sodium Lactate (Hartmanns’s) Solution

- Ringer Lactate

- Water For injection

- Sterile Water for Irrigation

- Sodium Chloride 0.9% for irrigation

- Sodium Chloride 0.18 – 0.45% and Glucose 4 – 10 %

- Potassium Chloride 0.15 – 0.3% in Sodium Chloride 0.9%

- Potassium Chloride 0.15 – 0.3% in Glucose 5%

The aims of IV fluid administration should be to

• Avoid dehydration

• Maintain an effective circulating volume

• Prevent inadequate tissue perfusion during a period when the patient is unable to achieve these goals through normal oral fluid intake

“Intravenous fluids have a range of physiologic effects and should be considered to be drugs with indications, dose ranges, cautions, and side effects.”

The intravenous route is the fastest way to deliver medications and fluid replacement throughout the body, because they are introduced directly into the circulation.

Intravenous therapy may be used for fluid volume replacement, to correct electrolyte imbalances, to deliver medications, and for blood transfusions.

Basic IV Setup

Let's take a look at the most basic possible setup for an IV:

The drip chamber is located just below the IV bag; inside this chamber we can see the fluid drip down from the bag into the IV tubing. This is where we measure the speed of a manual IV setup; we look at this chamber and count the number of drops we see per minute. So, for example, if we count 25 drops over the period of 60 seconds, we would say that the IV is infusing at a rate of 25 drops per minute, or 25 gtt/min. (In reality, we may not count the number of drops in a full minute; we can, for example, count the number of drops we see over a period of 15 seconds, and then multiply that number by 4 to get the number of drops in a full minute.)

The drip chamber must always be half full. If the drip chamber is too full, we will not be able to see the drops to count them, and so we will be unable to determine the rate at which the IV is infusing. If the drip chamber is not full enough, then this will allow air to get into the IV tubing, which means that air would get into the patient's circulatory system, which could be very dangerous, blocking a blood vessel or stopping the heart.

The roller clamp is what we use to control the rate at which the IV fluid infuses. If we roll it one way, it squeezes the IV tubing more tightly, making it narrower and therefore making the fluid flow through the tubing more slowly; if we roll it the other way, it loosens its pinching of the IV tubing, making the tubing less narrow, and allowing the IV fluid to flow through at a faster rate. So, if for example, we observe (by looking at the drip chamber and counting drops) that an IV is infusing at a rate of 50 gtt/min, but it was ordered to infuse at a rate of 30 gtt/min, we would tighten the roller clamp to slow the drip rate down until we could count only 30 drops going through the drip chamber each minute.

All roller clamps on a set of IV tubing should be closed before we attach a bag of IV fluid to the top of the tubing; this ensures that no air gets into the tubing.

Every IV medication will be ordered to infuse at a specific rate, and one of the major tasks of hosptial nurses is to set up the IV so that it infuses at this rate and to adjust the IV periodically if the rate has changed so that it remmains at the ordered rate. The rate at which an IV fluid infuses is referred to as the IV infusion rate or flow rate.

The slide clamp is used when we want to completely stop the IV from flowing, without having to adjust the roller clamp. This is handy if we want to stop the IV for a moment, but we don't want to have to reset the flow rate by readjusting the roller clamp all over again once we start the IV up again. This works by pinching the tubing completely shut when we slide the tubing into the narrowest part of the clamp.

The injection port is a place where medicine or fluids other than those in the current IV bag can be injected so that they will infuse into the patient's vein through the IV tubing. On the photo above we can see two ports: one on the IV bag itself and one below the drip chamber. There is also usually an injection port close to where the needle goes into the patient's vein; we'll see this below. The injection port on the actual IV bag is used if we want to mix some kind of medication with the fluid that is in the IV bag; if we inject the medication into this port and then roll the bag a little to mix the medication into the fluid in the bag, then the patient will recieve both the medication and the IV fluid at the same time. However, this can only be done when the IV fluid and the medication are allowed to be mixed. If we want to inject medication or a second kind of IV fluid directly so that it does not mix with the IV fluid that we've already attached, then we will use one of the ports that are located below the drip chamber.

The post I.V. FLUID MANUFACTURING UNIT appeared first on EIRI - eBooks and Project Reports.

The post I.V. FLUID (BFS TECHNOLOGY) appeared first on EIRI - eBooks and Project Reports.

The post I.V. FLUID (BFS TECHNOLOGY) appeared first on EIRI - eBooks and Project Reports.

In   nursing homes and hospital were patients are  suffering from  a cute dehydration or considerable debilitating conditions, the  intra venous fluids are used as IV drips. The basic  fuction of IV fluids is to replenish the body fluids. Although there  are a number of IV fluids are there  but generally three types of  IV fluidsd are used in hospitals as IV drips. They are as follows :

1. Dextrose injection fluid

2. Deretrose  and sodium chloride injection fluid

3. Sodium chloride injection solution (Saline solution).

PROJECT REPORT COVERS:

•     Introduction
•     Uses and Applications
•     Properties
•     Market Survey with future aspects
•     Present Manufacturers
•     B.I.S. Specifications
•     Manufacturing Process with Formulae
•    Cost Economics with Profitability Analysis
•     Capacity
•     Land & Building Requirements with Rates
•     List & Details of Plant and Machinery with their Costs
•     Raw Materials
•     Details/List and Costs
•     Power & Water Requirements
•     Labour/Staff Requirements
•     Utilities and Overheads
•     Total Capital Investment
•     Turnover
•     Cost of Production
•     Break Even Point
•     Profitability
•     Land Man Ratio
•     Suppliers of Plant & Machineries and Raw Materials.

The post I.V. FLUID (FFS TECHNOLOGY) appeared first on EIRI - eBooks and Project Reports.

1. Dextrose injection fluid

2. Dextrose  and sodium chloride injection fluid

Project Reports Cover:

•     Introduction
•     Uses and Applications
•     Properties
•     Market Survey with future aspects
•     Present Manufacturers
•     B.I.S. Specifications
•     Manufacturing Process with Formulae
•    Cost Economics with Profitability Analysis
•     Capacity
•     Land & Building Requirements with Rates
•     List & Details of Plant and Machinery with their Costs
•     Raw Materials
•     Details/List and Costs
•     Power & Water Requirements
•     Labour/Staff Requirements
•     Utilities and Overheads
•     Total Capital Investment
•     Turnover
•     Cost of Production
•     Break Even Point
•     Profitability
•     Land Man Ratio
•     Suppliers of Plant & Machineries and Raw Materials.

The post I.V. FLUID (FFS TECHNOLOGY) appeared first on EIRI - eBooks and Project Reports.

1. Dextrose injection fluid

2. Dextrose  and sodium chloride injection fluid

Project Report Covers:

Introduction
Uses and Applications
Properties
Market Survey with future aspects
Present Manufacturers
B.I.S. Specifications
Manufacturing Process with Formulae
Cost Economics with Profitability Analysis
Capacity
Land & Building Requirements with Rates
List & Details of Plant and Machinery with their Costs
Raw Materials
Details/List and Costs
Power & Water Requirements
Labour/Staff Requirements
Utilities and Overheads
Total Capital Investment
Turnover
Cost of Production
Break Even Point
Profitability
Land Man Ratio
Suppliers of Plant & Machineries and Raw Materials.

The post I.V. Fluid (FFS or BFS Technology) appeared first on EIRI - eBooks and Project Reports.