PROBLEMS WITH WASTE TYRES

The main problems with Tyre waste are as follows:

• Cause land and water pollution
• Cause health problems
• Can catch fire
• Non-biodegradable
• Un-aesthetic to view
• Expensive to get rid of
• Need reasonable space to stock

The post RECYCLING OF RUBBER TYRE AND EXTRACTION OF ALL BY PRODUCTS appeared first on EIRI - eBooks and Project Reports.

The post TYRE RECYCLING UNIT appeared first on EIRI - eBooks and Project Reports.

Automatic cleaning of heat exchangers and condensers tubes by means of sponge balls is well known since the early fifties, with expanding application from steam power plants to process industry to industrial cooling and air conditioning systems. Main benefits bottom-lined in cost savings are generally considered as: elimination of maintenance down-time and need for chemical and more efficient operation of process and plant.

The sponge rubber balls are necessary to maintain the inner side of condenser and heat exchanger tubes clean in power plants and process industries. Any kind of deposition inside the tube reduces the heat-exchange coefficient drastically. The sponge rubber balls can clean all the deposits on the inner side of the tube, and ensure that the equipment runs efficiently.

The cleaning balls are the active part of the tube cleaning system.

The choice of the ball type depends on the exchanger design and operating conditions. In particular water quality and flow, tubes material and sizes.

Benefits

Continuous injection of sponge balls through the exchanger tubes will prevent any build-up of scaling and/or biofouling. A clean tube means maintaining a high heat exchange rate and a power plant’s high electrical output. Technos cleaning balls are also highly efficient when used in other manufacturers’ equipment.

The post CONDENSER CLEANOUT SPONGE RUBBER BALLS appeared first on EIRI - eBooks and Project Reports.

Rice (Oryza sativa L.) has been the staple food for more than half of the humanity in the world or two-third of the World’s population. Rice is the seed or kernel of paddy, which is covered by two different layers, namely- bran (inner layer) and husk (outer layer). Literally, paddy becomes rice only when the two layers are removed properly through different milling processes. In the first step, brown rice is extracted by removing hull/husk from the paddy, which contains bran layer still intact around the kernel. In the second step, the bran layer is removed by polishing machine that rubs the grains together under pressure, and the output is the polished white kernel or fine rice, which is ready for cooking. The former process is known as hulling and the latter is known as milling of paddy. But, in short, it is the conversion ratio from paddy to rice, or one can term it as hulling and milling ratio. Therefore, the two terms-1) hulling and milling ratio; 2) conversion ratio, will be used interchangeably throughout this paper.

In term of production, India has become the second largest producer of rice in the world (21 per cent of global rice production), next to China. As on 2009, rough total production of paddy was 14, 8260 thousand MT in the country, but, as estimated by USDA, it was 13, 2013 thousand MT. On the demand side, India’s domestic consumption was, on an average, 95% of what it produced and was still the third largest exporter of rice, after Thailand and Vietnam, with about 20% of the world’s total rice exports in 2006-07. In the recent years, with the growth of population, more pressure on the arable land has been made and this in turn, the need for higher productivity of crops was felt in the country. At the same time, large quantity of foodgrain was reported to be lost due to inefficient milling processes in the country. Therefore, it calls for a better processing technique of rice to prevent processing loss.

Generally, rice kernels are often susceptible to breakage due to inefficient milling processes. Therefore, more efficient milling processes are highly recommended for better recovery ratio and quality rice kernel production. It is also identified as one of the most important remedies for preventing post-harvest loss and an issue that is widely recognized around the world.

The post DEHUSKING RUBBER ROLLER FOR RICE MILL appeared first on EIRI - eBooks and Project Reports.

Hoses, in fact are used for the transportation of fluid where pressure is present at high rate. Generally at low pressure rubber tubing is used. Gouses have wide range of applications. As stated earlier, special type of hose is suitable for each application some of these are listed below:-

1.      Air Hoses
2.      Acid Hoses
3.      Beverages Houses
4.      Blowing hoses
5.      Chemical Hoses
6.      Cement Hoses
7.      Creamery Hoses
8.      Dairy Hoses
9.      Fire Hoses
10.     Gas Hoses
11.     Hydraulic Hoses
12.     L.P.G. Hoses
13.     Oil Hoses
14.     Paint Spray Hoses
15.     Sand Blast Hoses
16.     Suction Hose
17.     Water hoses

Apart from these, there are also so many types of Hoses, which can not be giving here.

Another simple type of hose is produced on Barding or weaving cards or threads into tube or sewing strips of cotton duck into a tubular form. When the plain rubber tube and the plain fabric tube are combined and reinforced by metal we have making of an endless assessment of modern rubber Hose. In the typical industrial Hose, the inside tube is a simple extruded part which is covered by one or several reinforcing layers of woven fabric or by cards braided then to cover a rubber compound designed to resist wear and rough handling, is placed over the reinforcing plies. The tube reinforcing layers and cover are vulcanized into a single structure. Hose makers produce the products for specific types of service by varying the nature of number of reinforcing plies and also by adding further element - such as wire coiled around the inside or outside of the Hose or braided or woven into reinforcing layers.

INTRODUCTION
USES AND APPLICATION
B.I.S. SPECIFICATION
MARKET SURVEY
LOW PRESSURE HOSES
MEDIUM PRESSURE HOSES
HIGH PRESSURE HOSES
WATER SUCTION AND DISCHARGE HOSES
AIR AND GENERAL PURPOSE HOSES
CHEMICAL HOSES
PETROLEUM HOSES
DOCK AND CARGO HOSES
OTHER SPECIAL PURPOSES HOSES
DETAILED EXPORT DATA OF RUBBER HOSE PIPE
PRESENT MANUFACTURE OF RUBBER HOSES IN SMALL SCALE SECTORS
CHOICE OF HOSE
STRUCTURE AND MATERIALS
MANUFACTURING PROCESS
MANDREL - CURED CONSTRUCTION
WATER HOSE
STEAM HOSE
HOSE (TUBE AND COVER)
PROCESS FLOW DIAGRAM FOR MANUFACTURING RUBBER HOSE
MACHINERY REQUIRED
SUPPLIERS OF PLANT AND MACHINERY
RUBBER MIXING MILL
AIR COMPRESSOR
BOILERS
WEIGHING MACHINE (PLATFORM TYPE)
SUPPLIERS OF RAW MATERIALS
RECLAIMED RUBBERS
RUBBER CHEMICALS

APPENDIX – A:

1.      COST OF PLANT ECONOMICS
2.      LAND & BUILDING
3.      PLANT AND MACHINERY
4.      FIXED CAPITAL INVESTMENT
5.      RAW MATERIAL
6.      SALARY AND WAGES
7.      UTILITIES AND OVERHEADS
8.      TOTAL WORKING CAPITAL
9.      COST OF PRODUCTION
10.      PROFITABILITY ANALYSIS
11.      BREAK EVEN POINT
12.      RESOURCES OF FINANCE
13.      INTEREST CHART
14.      DEPRECIATION CHART
15.      CASH FLOW STATEMENT
16.      PROJECTED BALANCE SHEET

The post RUBBER HOSE PIPE appeared first on EIRI - eBooks and Project Reports.

School shoes are used for protecting the children foot from injuries due to stones nails, broken glass pieces infection from dust diet, mud, water and to feel conform during different climatic condition.

Children shoes in particular are very important in order to save the foot. School shoes are very common part of school uniform introduced by many Government and Public School.

Canvas shoes are used as footwear by all groups of people. It  is made of thick cloth and sole of soft rubber sheets.  Large number  of  variations  in  quality  of  canvas  sheet  and  sole materials  are  used for different purposes  and  selling  price. Canvas  shoes  are  available  in  different  sizes  and  designs suitable according to one's need and liking.

Traditionally, footwear was manufactured by hand assembling, preshaped  component parts on a lst or tree and vulcanizing in  a autoclave.   Although this method is still used but a great  deal of  advances  in machinery, equipment  and  automated  processes, thereby  reducing the high labour content of the  hand  assembled product.

The canvas footwear industry has also taken advantage of new developments  in  polymer  science &  technology  to  formula  to compounds which meet the new process requirements & give products with practically any desired feature.

INTRODUCTION
INTRODUCTION
USES AND APPLICATIONS
CLASSIFICATION OF SAFETY SHOES
SAFETY-TOE SHOES
CONDUCTIVE SHOES
FOUNDRY SHOES
EXPLOSIVE - OPERATIONS (NON-SPARKING) SHOES
ELECTRICAL HAZARD SHOES
OTHER TYPES OF SAFETY SHOES
CARE OF FOOT AND LEG PROTECTION EQUIPMENT
SPECIFICATIONS FOR DIFFERENT
TYPES OF SAFETY SHOES
LEATHER SAFETY BOOTS AND SHOES [IS: 1989 (PART-1 & 2)-1986]:
FIREMAN’S LEATHER BOOTS (IS: 4128-1980):
ELECTRICAL SAFETY SHOES:
CHEMICAL SAFETY SHOES:
ELECTRICAL-CUM-CHEMICAL GUM BOOTS:
SHOES SUITABLE FOR MINING OPERATIONS:
MARKET SURVEY OF INDUSTRIAL SAFETY BOOTS
INDUSTRIAL PROTECTIVE FOOTWEAR MARKET: BY TYPE
INDUSTRIAL PROTECTIVE FOOTWEAR MARKET: BY APPLICATION
OVERVIEW OF GLOBAL FOOTWEAR MARKET
ASIA-PACIFIC FOOTWEAR MARKET SCENARIO
VALUE CHAIN ANALYSIS
B.I.S. SPECIFICATION
RUBBER SOLE RAW MATERIAL
THICKNESS
MANUFACTURE OF SCHOOL SHOES
THE PROCESS IS DIVIDED IN FOUR DEPARTMENTS VIZ;
PROCESS FLOW DIAGRAM
PROCESS OF MANUFACTURE FOR CANVAS SHOES FOR COAL MINES
THE OUTLINE OF PROCESS OF MANUFACTURE IS AS FOLLOWS
HOWEVER, THE COMPLETE PROCESS OF MANUFACTURE CAN
BE SPLIT INTO FOLLOWING MAJOR STEPS I.E.
THE DETAILED STEPWISE PROCESS IS AS FOLLOWS
ADHESIVE ATTACHMENT
MOULDING PROCESS CAN BE CLASSIFIED INTO TWO TYPES.
PROCESS FLOW SHEET FOR THE MANUFACTURE OF CANVAS SHOES
FOR COAL MINES
PROPERTIES OF SHOE FABRICS (CANVAS) FOR COAL MINES
PHYSICAL PROPERTIES:
STRENGTH:
TENSILE STRENGTH:
TEAR STRENGTH
STRECH:
BALANCE OF STRENGTH & STRETCH:
SHOE FABRIC SPECIFICATION
TYPICAL SPECIFICATIONS OF SHOE LINING FABRICS
SAME STANDARD SPECIFICATIONS OF SHOE LINING FABRICS
RUBBER SOLE: ANCILLARY ITEM FOR CANVAS SHOE
USES OF RUBBER IN FOOTWEAR TRADE
USE OF VULCANISED SOLES AND HEELS
FORMULATION OF SAFETY BOOTS (UPPER)
FORMULATION OF SAFETY BOOTS (SOLE)
FORMULATION OF SOLE FOR SCHOOL SHOES
FORMULATION OF SOLE MAKING
A. BLACK SOLE MIX
B. BROWN SOLE MIX
IMPLEMENTS & TYPES OF MACHINERIES SHOE LASTS
COMPRESSION MOULDED FOOTWEAR
MOULDING PRESSES CAN BE CLASSIFIED INTO TWO TYPES
INJECTION MOULDING OF SOLES & HEELS
RUBBER SOLE MANUFACTURING
PLASTICIZING
INJECTIONS
AFTER FILLING
COOLING AND MOULD RELEASE
MANUFACTUREING PROCESS OF SAFETY BOOTS
THE PROCESSING IS DIVIDED IN DEPARTMENTS VIZ.
1. RUBBER SECTION
2. COMPRESSION MOULDED INDUSTRIA
4. ASSEMBLY SECTION
5. FINISHING & PACKING SECTION
PREPARATION OF RUBBER MIX
VULCANISATION OF SOLES
PROCESS FLOWSHEET FOR MANUFACTURE OF SAFETY BOOTS
MANUFACTURING PROCESS OF NITRITE BOOTS
PROCESS OF SHOE MAKING
CLICKING OR CUTTING DEPARTMENT
CLOSING OR MACHINING DEPARTMENT
LASTING & MAKING DEPARTMENT
FINISHING DEPARTMENT AND THE SHOE ROOM
TESTING AND INSPECTION OF SAFETY BOOTS
INSPECTION OF FINISHED PRODUCT
PLANT LAYOUT
SUPPLIERS OF RAW MATERIALS
SUPPLIERS OF PLANT AND MACHINERY

APPENDIX – A:

1.      COST OF PLANT ECONOMICS
2.      LAND & BUILDING
3.      PLANT AND MACHINERY
4.      FIXED CAPITAL INVESTMENT
5.      RAW MATERIAL
6.      SALARY AND WAGES
7.      UTILITIES AND OVERHEADS
8.      TOTAL WORKING CAPITAL
9.      COST OF PRODUCTION
10.      PROFITABILITY ANALYSIS
11.      BREAK EVEN POINT
12.      RESOURCES OF FINANCE
13.      INTEREST CHART
14.      DEPRECIATION CHART
15.      CASH FLOW STATEMENT
16.      PROJECTED BALANCE SHEET

The post MANUFACTURING SHOES (SAFETY BOOTS & SCHOOL SHOES) USING RUBBER POWDER appeared first on EIRI - eBooks and Project Reports.

The rubber conveyor belt is usually manufactured by laminating a number of plies of a rubberized textile reinforcement, and consolidating and vulcanizing them in a special press or rotary curing machine.

The natural rubber with its excellent building tack has two wide use for the manufacturing of beltings of every specifications and kinds for ply construction and cover where SBP is also used.

Regarding the other rubbers for making belts. Such as butyl rubber has good resistance to ozone abrosion and vegetable oils but ply adhesion is poor due to moisture held in fabric cannot reedily escape. Nitrile and neoprene rubbers can be used in the cover compounds in the specific purpose belts.

Rubber conveyor belting essentially consists of various fabrics like all cotton, cotton/nylon, rayon/nylon, all synthetic etc. with a cover of various rubber grades like oil resistant, flame resistant etc. The design of conveyor belt cover compound is most important in determining the service life of the belt in any particular application. Heat and flex-cracking resistance being the essential requirements of conveyor belts in service, different types of anti-oxidants are used for heavy, medium and light duty belts.

INTRODUCTION
TYPES OF RUBBER CONVEYOR BELTS
CONSTRUCTION
TEXTURES
THREE COMMON DESIGNS OF FLAT BELTS INCLUDE:
THREE VERSATILE FABRIC DESIGNS:
PROPERTIES
USES AND APPLICATIONS
B.I.S. SPECIFICATION
MARKET SURVEY
CONVEYOR BELT MARKET IN INDIA 2012-2016
GLOBAL CONVEYOR BELT MARKET 2016-2020
OVERVIEW OF THE GLOBAL CONVEYOR BELT MARKET
SWOT ANALYSIS
MANUFACTURERS/SUPPLIERS OF RUBBER CONVEYOR BELT
MANUFACTURING PROCESS
COMPOUNDING AND MIXING
CALENDERING
QUALITY CONTROL
THICKNESS OF RUBBER COVER:
PLANT LAYOUT
SUPPLIERS OF RAW MATERIALS
SUPPLIERS OF NATURAL RUBBER
SUPPLIERS OF SYNTHETIC RUBBER
SUPPLIERS OF FABRIC FOR CONVEYOR BELT
SUPPLIERS OF CARBON BLACK
SUPPLIERS OF ZINC OXIDE, STERIC ACID AND SULPHER
SUPPLIERS OF COLOUR PIGMENT
SUPPLIERS OF PACKING MATERIALS
SUPPLIERS OF PLANT AND MACHINERY
SUPPLIERS OF MIXING MILL
SUPPLIERS OF RUBBER DISPERSION KNEDER AND CALENDER
SUPPLIERS OF VULCANISING PRESS
SUPPLIERS OF STEAM BOILERS
MEASURING AND TESTING INSTRUMENTS
SUPPLIERS OF DG SETS
SUPPLIERS OF POWER TRANSFORMERS
SUPPLIERS OF COOLING TOWER
SUPPLIERS OF ETP PLANTS
AIR POLLUTION CONTROL EQUIPMENTS
AIR CONDITIONING EQUIPMENTS
AIR COMPRESSORS
WEIGHING MACHINE (PLATFORM TYPE)
MATERIAL HANDLING EQUIPMENTS
FIRE FIGHTING EQUIPMENTS
SUPPLIERS OF SUBMERSIBLE WATER PUMP

APPENDIX – A:

1.      COST OF PLANT ECONOMICS
2.      LAND & BUILDING
3.      PLANT AND MACHINERY
4.      FIXED CAPITAL INVESTMENT
5.      RAW MATERIAL
6.      SALARY AND WAGES
7.      UTILITIES AND OVERHEADS
8.      TOTAL WORKING CAPITAL
9.      COST OF PRODUCTION
10.      PROFITABILITY ANALYSIS
11.      BREAK EVEN POINT
12.      RESOURCES OF FINANCE
13.      INTEREST CHART
14.      DEPRECIATION CHART
15.      CASH FLOW STATEMENT
16.      PROJECTED BALANCE SHEET

The post RUBBER CONVEYOR BELTS appeared first on EIRI - eBooks and Project Reports.

Earlier polyester tyre cords were popular but were gradually replacing by nylon tyre cord fabric. Nylon cord provides reinforcement for all types of tyres.

Nylon tyre cord (NTC) is made from high tenacity continuous filament yarn by twisting and plying . The major criteria for acceptance of any material in tyre are its tensile, strength dimensional stability, thermal stability hysteresis and adhesion.

However, with the emergence of redial tyres even nylon tyre cord fabric face  only modest prospects in the coming future, Polyester tyre cord is used to a very small extent and the bulk of it is imported rather than produced domestically.

INTRODUCTION
TYPES OF TYRE CORD
PROPERTIES OF NYLON 66
STRUCTURE OF TYRE CORD FABRIC
PROPERTIES & CHARATERISTICS
PROPERTIES OF TIRE CORD FABRIC
USES OF TYRE CORD FABRIC
MARKET SURVEY
MARKET SIZE ESTIMATION OF TYRE CORD
IMPORT DATA OF TYRE CORD FABRIC
GLOBAL MARKET POSITION OF TYRE CORD FABRIC
OVERVIEW OF TYRE INDUSTRY IN INDIA
PRESENT MANUFACTURES/SUPPLIERS OF TYRE CORD FABRIC
MANUFACTURING PROCESS OF TYRE CORD FABRIC
PROCESS FLOW DIAGRAM
SEQUENCES IN TYRE CORD MANUFACTURE
PROCESSING DETAILS OF NYLON CORD FABRIC FROM CAPROLACTAM
PROCESS FLOW DIAGRAM
TYRE CORD MANUFACTING PROCESS IN DETAILS
TESTING METHOD OF TIRE CORD FABRIC
PLANT LAYOUT
PRINCIPLES OF PLANT LAYOUT
PLANT LOCATION FACTORS
EXPLANATION OF TERMS USED IN THE PROJECT REPORT
PROJECT IMPLEMENTATION SCHEDULES
DETAILS OF MACHINERY & SPECIFICATION
SUPPLIERS OF RAW MATERIALS
SUPPLIERS OF PLANT AND MACHINERY

APPENDIX – A:

1.      COST OF PLANT ECONOMICS
2.      LAND & BUILDING
3.      PLANT AND MACHINERY
4.      FIXED CAPITAL INVESTMENT
5.      RAW MATERIAL
6.      SALARY AND WAGES
7.      UTILITIES AND OVERHEADS
8.      TOTAL WORKING CAPITAL
9.      COST OF PRODUCTION
10.      PROFITABILITY ANALYSIS
11.      BREAK EVEN POINT
12.      RESOURCES OF FINANCE
13.      INTEREST CHART
14.      DEPRECIATION CHART
15.      CASH FLOW STATEMENT
16.      PROJECTED BALANCE SHEET

The post TYRE CORD FABRICS MANUFACTURE appeared first on EIRI - eBooks and Project Reports.

The manufacturing of automobile tyres as an essential ancillary for the development of automobile sector came into being in India during 1930's when the Dunlop India Ltd, the first tyre manufacturing transnational company started its operation in 1935 at Sahaganj in West Bengal.

Today, one cannot imagine a world without automobiles even though India has a large network of railway lines, considering the vastnes of the country and the thrust given for balanced development, road transport would have decisine role to play in the coming years. Vehicle would become more and more part of  not only the commercial like but even the personal like.

The Indian tyre and tube industry has been continuously in the process of up gradation of product quality to satisfy the requirements of Indian automotive manufactures, users of automobiles and the road conditions prevailing in the country. Various developments have taken place in design of tyres especially for passenger cars, light trucks, trucks and buses involving tyre construction, strength, sizes, tread design, rubber compounding etc. The pace of development of tyres in the country has also been hastened by the requirements of new passenger car and light truck manufactures and for export, which require higher accuracies, better uniformity longer life etc.

INTRODUCTION
BUREAU OF INDIAN STANDARDS
LABORATORY TESTING OF TIRE COMPOUND
COMPONENTS OF TYRES
PROPERTIES AND CHARACTERISTICS OF RADIAL TYRES
RAW MATERIALS
DETAILS OF COMPONENTS IN TYRE BUILDING
GLOBAL MARKET POSITION OF TYRE INDUSTRY
MARKET SURVEY
PRESENT MANUFACTURERS/EXPORTERS OF RADIAL TYRE
TECHNICAL KNOW - HOW
FOREIGN COLLABORATIONS
MANUFACTURING PROCESS OF PASSENGER CAR TYRE
TECHNICALITIES IN TYRE PLANT
FORMULATION OF TRUCK TYRE (RADIAL)
FORMULATION OF CAR TYRE (RADIAL)
MANUFACTURING PROCESS OF RADIAL TYRES
PROCESS FLOW DIAGRAM OF RADIAL TYRE
PROCESS IN DETAILS
DIFFERENT OPERATION IN RADIAL TYRE MANUFACTURING
PASSENGER CAR TYRE FORMULATION (RADIALS)
TRUCK TYRE FORMULATION (STEEL RADIAL)
FORMULATION OF TYRES COMPOUNDS
RECIEPES FOR AUTOMOBILE BEAD WIRE
POST MANUFACTURING METHOD FOR RADIAL TYRES
MANUFACTURING PROCESS OF RUBBER POWDER FROM USED TYRE
PROCESS FLOW DIAGRAM
STEPS OF PROCESSING WASTE TYRE TO RUBBER POWDER
NEW PROCESS AND TREND FOR WASTE TYRES TO RUBBER POWDER
PLANT LAYOUT
SUPPLIERS OF PLANT AND EQUIPMENTS (GLOBAL)
SUPPLIERS OF PLANT AND EQUIPMENTS
SUPPLIERS OF RAW MATERIALS
DETAILS OF MACHINERY
COMPOSITION OF PASSENGER TYRE
FORMULATION REQUIRED/MONTHS

APPENDIX – A:

1.      COST OF PLANT ECONOMICS
2.      LAND & BUILDING
3.      PLANT AND MACHINERY
4.      FIXED CAPITAL INVESTMENT
5.      RAW MATERIAL
6.      SALARY AND WAGES
7.      UTILITIES AND OVERHEADS
8.      TOTAL WORKING CAPITAL
9.      COST OF PRODUCTION
10.      PROFITABILITY ANALYSIS
11.      BREAK EVEN POINT
12.      RESOURCES OF FINANCE
13.      INTEREST CHART
14.      DEPRECIATION CHART
15.      CASH FLOW STATEMENT
16.      PROJECTED BALANCE SHEET

The post TYRE MANUFACTURING FROM RECYCLED TYRES/RUBBER POWDER ALONGWITH OTHER RAW MATERIALS appeared first on EIRI - eBooks and Project Reports.

The rubber solution which are manufactured by synthetic rubber are called as "synthetic rubber adhesives". It is an important item for shoes and rubber industries in the joining of two layers or more than two rubber layers of shoe layers or shoe parts and soles. The rubber solutions have some public uses also, such as, in cycle puncture and heavy vehicle puncture fixing.

Rubber cement is a solution of unvulcanized (gum) rubber in a solvent, and is used as an adhesive. Ideally, it is meant to join two pieces of rubber together, which involves a chemical cohesion process. When joining two pieces of rubber, only one surface has to be coated with rubber cement since they are the same material. However, when joining paper together, both pieces need to be covered with rubber cement. When rubber cement dries, only the parts in contact with the paper remain, which holds the two pieces together. Despite this limitation, the household type of rubber cement finds wide use for applications such as mounting photographs. Unlike with white glue, the joined pieces of paper can be pulled apart without damaging either piece.

Adhesives are made from either natural animal or plant products or synthetic polymer. Natural adhesives are easy to apply and in general are water soluble.

Synthetic adhesives are divided into four chemical categories: thermoplastic, thermosetting, elastomeric, and combinations thereof. Thermoplastic adhesives, such as polyvinyl alcohol and acrylics, can be resoftened since the materials do not crosslink upon curing. They require heat or a solvent to create a bond.

Thermosetting adhesives, which include epoxies, cannot be heated and resoftened after curing because they do crosslink upon curing. Elastomeric adhesives are based on isoprene rubber or synthetic polymers that combine both elasticity and toughness. Silicone is a typical example.

INTRODUCTION
USES AND APPLICATION
B.I.S. SPECIFICATION
MARKET SERVEY
MANUFACTURES/SUPPLIERS OF LATEX BASED RUBBER ADHESIVES
SPECIFICATION OF SHOE ADHESIVE, NATURAL RUBBER LATEX BASED
PROPERTIES OF LATEX BASD RUBBER ADHESIVES VERSUS SOLVENT BASED ADHESIVE
ADVANTAGE OF LATEX ADHESIVE OVER RUBBER SOLUTION
RAW MATERIALS
PROPERTIES
FORMULATIONS FOR WATER BASED LATEX ADHESIVES
FORMULATIONS
FORMULATION OF LATEX ADHESIVE FOR FOOTWEAR
FORMULATION OF ADHESIVE FORMULATION (CHLOROPRENE BASED)
FORMULATION OF POLYCHLOROPRENE BASED RUBBER ADHESIVE
(MULTI PURPOSE)
FORMULATION OF SBR ADHESIVE
RAW MATERIALS CALCULATION
MANUFACTURING PROCESS OF LATEX BASED ADHESIVES
PROCESS FLOW DIAGRAM
MANUFACTURING PROCESS OR RUBBER CEMENT
PLANT LAYOUT
PRINCIPLES OF PLANT LAYOUT
PLANT LOCATION FACTORS
EXPLANATION OF TERMS USED IN THE PROJECT REPORT
PROJECT IMPLEMENTATION SCHEDULES
SUPPLIERS OF PLANT & MACHINERY
SUPPLIERS OF RAW MATERIALS

APPENDIX – A:

1.      COST OF PLANT ECONOMICS
2.      LAND & BUILDING
3.      PLANT AND MACHINERY
4.      FIXED CAPITAL INVESTMENT
5.      RAW MATERIAL
6.      SALARY AND WAGES
7.      UTILITIES AND OVERHEADS
8.      TOTAL WORKING CAPITAL
9.      COST OF PRODUCTION
10.      PROFITABILITY ANALYSIS
11.      BREAK EVEN POINT
12.      RESOURCES OF FINANCE
13.      INTEREST CHART
14.      DEPRECIATION CHART
15.      CASH FLOW STATEMENT
16.      PROJECTED BALANCE SHEET

The post LATEX BASED RUBBER ADHESIVES WITH PROCESS AND FORMULAE appeared first on EIRI - eBooks and Project Reports.